bike75.gif (2872 bytes)

"Knowledge is the key to improving your cycling performance."

- CPT mission statement -

Bicycle Tires Gig Harbor WA

Local resource for bicycle tires in Gig Harbor. Includes detailed information on local businesses that provide access to road bike tires, racing bike tires, city bike tires, mountain bike tires, recumbent tires, bicycle tubes, bicycle pumps, bicycle tools, as well as advice and content on bicycle accessories.

Old Town Bicycle Incorporated
(253) 858-8040
6820 Kimball Dr, #B1
Gig Harbor, WA
Big 5 Sporting Goods
(253) 851-2172
4811 Point Fosdick Dr NW
Gig Harbor, WA
Kamakaze Mountain Bike Club
(253) 857-3002
3959 Regatta CT
Gig Harbor, WA
Tack To You
(253) 884-6688
15706 140th Avenue Kp N
Gig Harbor, WA
Rafter L Saddlery
(253) 906-4362
5408 36th Ave NW APT A202
Gig Harbor, WA
Lesters Soccer Source
(253) 851-7511
2002 36th St NW
Gig Harbor, WA
Russ Haydons Shooters Supply
(253) 857-7557
15018 Goodrich Dr NW
Gig Harbor, WA
Puget Sound Herring Sales Inc
(253) 858-2201
P.O. BOX 275
Gig Harbor, WA
Old Town Bicycle
(253) 858-8040
6820 Kimball Dr # B1
Gig Harbor, WA
Hurt Guns
(253) 858-6998
5102 61st St NW
Gig Harbor, WA

Brakes, Rims, & Wheels



Brake Pads

After you have been riding in the rain or suboptimal road conditions, you will notice a sound of metal on metal when you brake. Generally this is from grit picked up by the pads. Over time, this additional abrasion can accelerate wearing down of the rim metal itself.

To clean pads, pick out the larger pieces of foreign material with an awl, penknife or the tip of a small screwdriver. While you are at it, check the grooves on the pad. If it has been a few years, consider replacing pads if they have hardened with age.

A smooth rim will also improve braking performance. But you don't want to go overboard and remove the metal itself. A Scotch-Brite pad works well for this purpose. It's a gentle abrasive that won't remove material from the rim but will take off rubber deposits to ensure optimum braking.


Sealed Hub Maintenance

To check for maintenance status remove the wheels from the bike. Turn the axles slowly with your fingers - you will feel a slight but smooth hydraulic resistance. If an axle either turns roughly or spins freely with no resistance, you need to do some maintenance. Roughness can indicate damaged bearings, too little resistance means the lubrication is gone, usually because it's been washed out by lots of rainy rides or improper bike-cleaning techniques (using high-pressure sprayers or getting solvent into the bearings).

Rear hubs are a bit more complicated to handle, front hubs are more user friendly. It does help to have the right tools. To regrease a hub, pull off the dust caps or pry them out by carefully wedging an X-Acto blade between each cap and hub. You'll see the plastic seals covering the bearings. Lift these by slipping the blade beneath, being very careful not to bend the seals.

Once you see the bearings, you can add grease if they're just dry, or take the extra step of cleaning them with solvent, drying them, and repacking them if they're gritty. The seals will pop back into place with gentle hand pressure.

Wheels and Rims

It is true that the more weight further from the hub, the harder it is to accelerate a wheel. Total wheel weight is related to the number (and weight) of the spokes, but even more important is the rim itself. So if you have fewer spokes, but need a stronger (read heavier) rim, the over all performance improvement is a negative.

Think about it, if you are considering low-spoke-count wheels, they almost never list the weight of the rims . In...

Click here to read the rest of this article from CYCLING PERFORMANCE TIPS

Performance Quiz | Appendix | Index/Glossary | Site Map | Contact